Black Box LPS500A Gigabit PoE Media Converter to Multi/Singlemode Fiber, LC or SC

Black Box LPS500A Gigabit Ethernet PoE Media Converter, Multi/Single Fiber, 850nm, 500m, LC
Model: LPS500A
Availability: Contact Westward Sales
Standard Shipping & Handling

Choose Options


* Fiber Interface:

Qty: Add to Cart

Black Box LPS500A Gigabit Ethernet PoE Media Converter, Multi/Singlemode, LC or SC Connectors

Connect Gigabit-speed fiber optic to a 10-/100-/1000-Mbps copper UTP segment while also powering 802.3af devices at the end of the CAT5 run. The LPS500A unmanaged PoE Gigabit Media Converter from Black Box enables you to transparently connect copper cabling to multimode fiber as an economical way to extend Ethernet communications well beyond the 100-meter (327-foot) CATx limit.

Along with matching copper to interference-free fiber at Gigabit speeds, the LPS500A doubles as power sourcing equipment (PSE) for Power over Ethernet (PoE) devices plugged in on the copper side. Using existing UTP cabling for both data communications and 48-VDC power simplifies a network application in terms of provisioning power and maintaining equipment.

It's particularly ideal for locating equipment where electrical access is inconvenient or just too expensive to locate. Install PoE-compatible security cameras and wireless access points in areas without any nearby power outlets while reducing your overall power consumption, too. Plus, the PoE PSE Gigabit Media Converter has extensive power management features, including overcurrent protection, undercurrent detection, minimum load sensing, and PSE MDI power enable/disable.

For reliable data communications, the LPS500A boasts link fault pass-through (LFP) capabilities, monitoring receive ports on both the fiber and copper sides for loss of signal. If signaling is lost on one media port, it automatically disables the transmit (TX) signal to the other media port. A far-end fault (FEF) function enables the converter to cease sending a link pulse to a link partner if signaling on the fiber receive (RX) port is lost. The link partner will also synchronously stop sending data. This way, you don't lose valuable data transmitted over an invalid link.

Key Features of the LPS500A

  • Supports up to 30 W, 802.3at
  • Compliant to EN62368
  • A low-cost, economical solution for powering PoE devices CATx
  • Available with LC or SC connectors
  • DIP switch sets PoE, LFP, and normal/cut-through configurations
  • Powered device (PD) signature sending detects when a PoE device is connected
  • Protects against damage caused by overcurrent events and offers undercurrent detection
  • Link fault passthrough monitors both copper and fiber receive ports for loss of signal
  • Far-end fault detection prevents the loss of valuable data from it being sent over an invalid link
  • Copper port auto negotiates for network speed and features Auto MDI-X for easy cabling
  • LEDs indicate when it is feeding PoE power as well as when power is interrupted
  • 1 Year Double Diamond™ Warranty (Standard) included

Configurations

LPS500A-MM-LC-R3, Multimode (500 m) Fiber Media Converter with LC Connectors
LPS500A-MM-SC-R3, Multimode (550 m) Fiber Media Converter with SC Connectors
LPS500A-SM-10K-LC-R3, Singlemode (10 km) Fiber Media Converter with LC Connectors

In the Box

  1. 10/100/1000BASE-T to 1000BASE-X PoE PSE GbE Media Converter
  2. AC Power Cord
Technology
CategoryMedia Converter
Media Converter TypeFiber to Gigabit Ethernet
Fiber InterfaceSC Connector | LC Connector
StandardsIEEE 802.3af (PoE), IEEE 802.3 (10BASE-T), IEEE 802.3u (100BASE-TX), IEEE 802.3z/ab (1000BASE-T), IEEE 802.3x full-duplex flow control, 1000BASE-SX
Transmission DistanceUTP side: 100 m (328 ft.); Fiber side (850-nm multimode): 62.5/125-µm: 160-MHz: 220 m (721 ft.); 200-MHz: 275 m (902.2 ft.); 50/125-µm: 400-MHz: 500 m (1640 ft.); 500-MHz: 550 m (1804.4 ft.)
Power
PoE Power OutputAvailable power: 30 W; Number of ports that support PoE: (1) PoE port supports PoE within available PoE power
Rated PowerRequirement: 100-240 VAC, 47-63 Hz; Consumption (maximum): Up to 65 W
Ratings
Operating Temperature32 to 122° F (0 to 50° C)
Storage Temperature-4 to +158° F (-20 to +70° C)
Humidity5 to 95% noncondensing
Altitude10,000 feet (3125 m) maximum
Download NameFile Size
Black Box LPS500A Datasheet107.53KB
Black Box LPS500A Manual314.07KB